General portable-power-tools RAMS can cover a defined set of routine activities, but not an open-ended permission to use any powered tool. The document should connect each task to the named tool, compatible attachment, material, power source, guarding, workpiece support, dust control, noise and vibration assessment, competence, inspection and exclusion arrangements. A tool or activity with materially different hazards needs a task-specific assessment and method.
The starting point is the work, not the toolbox. A cordless drill used to drive screws into pre-checked timber presents a different combination of hazards from drilling masonry, chasing concrete, cutting metal or sanding a coating—even if the same operative carries out every task.
This guide deals with general management of portable tools on construction projects. It complements the project's RAMS arrangements and the relevant trade method; it does not replace manufacturer instructions, COSHH assessments, permits, exposure assessments or specialist training.
Can one RAMS cover several portable power tools?
Yes, where the scope is narrow, the tools and activities are known, the hazards and controls are genuinely compatible, and the resulting document remains clear enough to brief and supervise. A small installation package might group cordless screwdrivers, a low-torque drill and a suitable vacuum where the substrates, fixings and work area have been confirmed.
Separate or task-specific RAMS are normally needed where the method introduces a different risk profile: abrasive wheels, disc cutting, chainsaws, cartridge-operated tools, breaking or chasing, hot work, wet cutting near electricity, work in a confined space, work at height with a tool, work on or near live systems, or substantial silica, wood-dust, noise or vibration exposure.
The document should state its boundaries. “Portable power tools” is a category of equipment, not a complete description of construction work.
Build a tool-task-material register
A short register or schedule makes a general tool RAMS auditable. For every planned activity, record:
- the task, exact location and responsible trade;
- the tool make, model or defined type and its intended use;
- the bit, blade, disc, wheel, pad, cutter or other accessory, including size and speed rating where relevant;
- the material or substrate and whether asbestos, lead, silica, wood dust, hidden services or other hazards may be present;
- the power source, voltage, battery system, transformer, leads and protective devices;
- the required guard, handle, extraction shroud, workpiece restraint and exclusion zone;
- the manufacturer information, competence or authorisation needed;
- the dust, noise and vibration controls and expected trigger time;
- the pre-use and periodic inspection arrangements; and
- the stop-work conditions that require reassessment.
This schedule prevents a common failure: a worker bringing a different attachment or using the same tool on a different material without anyone checking compatibility, exposure or the method.
What should be checked before work starts?
Confirm the current drawing or specification, workface, substrate, fixing or finish, access, lighting, other trades and people who may be affected. Check service information and the relevant asbestos survey before drilling, cutting or disturbing existing building fabric. Obtain current manufacturer instructions for the tool and accessory rather than relying on familiarity with a similar model.
For hired, borrowed or worker-owned equipment, confirm who controls selection, inspection, maintenance, records and removal of defective tools. Ownership does not remove the employer's or person-in-control's work-equipment duties.
Estimate actual daily exposure across all tools. Several short periods of hammer drilling, grinding or sanding contribute to the same worker's overall shift exposure; resetting the count for each task understates the risk.
Set out a controlled sequence
- Confirm the task, material, location and permitted tool against the approved register.
- Check design, service, asbestos and product information; obtain any required permit or isolation.
- Select the correct tool, compatible accessory, guard, handle, extraction, power arrangement and workpiece support.
- Inspect the tool, plug, lead, battery, charger, controls, guard and accessory before use; quarantine defects.
- Prepare stable access and lighting, secure the material, route leads safely and establish the necessary exclusion area.
- Connect extraction or other engineering controls and check that they work before creating dust or debris.
- Brief the operator on the method, exposure limits, emergency arrangements and stop-work conditions.
- Use the tool within its intended capacity and position; keep guards fitted and hands away from the danger zone.
- Switch off, isolate and wait for movement to stop before adjustment, cleaning, clearing a blockage or changing an accessory.
- Inspect the work, remove dust and waste safely, record defects and store the tool, accessories and batteries securely.
Critical controls for portable power tools
Suitability, accessories and guarding
HSE explains that PUWER covers tools used at work and requires work equipment to be suitable, maintained and used by people given adequate information, instruction and training. Match the tool and accessory to the task and material. Confirm accessory dimensions, mounting, direction and maximum speed; never improvise a fit or defeat a guard or safety control.
Support or clamp the workpiece where practicable. Consider kickback, binding, ejected fragments, reaction torque and the line of cut or drill. Side handles and other supplied safety devices must be used where the manufacturer requires them.
Inspection, defects and maintenance
Define what the operator checks before use and what competent inspection or maintenance is required at suitable intervals. The interval should reflect the tool, environment, frequency of use, manufacturer information and experience of deterioration; a sticker alone does not prove that a tool is safe today.
Provide a clear quarantine route. Damaged guards, controls, casings, plugs, leads, batteries, chargers or accessories should be labelled and removed from use so that another person cannot pick them up. Repairs and maintenance must be carried out safely by competent people with the equipment shut down and isolated.
Electricity and batteries
On construction sites, HSE advises using cordless tools or a 110 V centre-tapped-to-earth supply so that the maximum voltage to earth does not exceed 55 V. An RCD detects some, not all, electrical faults, so it does not replace safe selection, inspection, cable protection, earthing or isolation.
Keep transformers and connections in suitable locations, protect leads from traffic, water, sharp edges and trip routes, and do not overload supplies. Follow manufacturer requirements for charging and storing batteries. Quarantine batteries that are damaged, swollen, unusually hot, wet or otherwise suspect, and plan how a battery fire or thermal event will be reported and managed under the site emergency arrangements.
Dust and hazardous materials
Identify the material before choosing a control. Cutting, grinding, drilling and surface preparation can create respirable crystalline silica, wood dust, metal particles, coating residues or other harmful substances. Use a lower-dust method where possible and suitable on-tool extraction or water suppression where it is compatible with the tool, material and electrical arrangements.
HSE's construction-dust guidance treats on-tool extraction as a system: the tool, extraction hood, correctly classed vacuum, hoses and filters must work together and be maintained. RPE may still be needed after engineering controls, but it must be selected from the residual risk, face-fit requirements and wearer suitability. Do not use dry sweeping to deal with fine construction dust.
Noise and hand-arm vibration
Assess the tool's actual use and daily exposure, including time spent on different vibrating tools. HSE states a hand-arm vibration exposure action value of 2.5 m/s² A(8) and exposure limit value of 5 m/s² A(8). These are not target working levels; exposure should be prevented or reduced so far as reasonably practicable.
Select lower-noise and lower-vibration methods and equipment, maintain cutters and consumables, avoid unnecessary trigger time and use reliable exposure information. Job rotation cannot be the only control and does not remove the need to reduce risk. Where hearing protection is required, specify the zone, selection, compatibility with other PPE, supervision and arrangements for communication and warning signals.
Access, environment and other people
Choose access equipment that lets the operator control the tool without overreaching, excessive force or an unstable stance. Manage trailing leads, hoses, falling objects, sparks, debris, poor lighting, water and nearby combustible materials. A tool should not be operated from a ladder simply because the job is brief.
Set an exclusion area that reflects the possible travel of fragments, sparks, dust, the workpiece and the tool if it snatches. Coordinate the task with other trades and occupants, and keep escape routes and fire precautions effective.
When general portable-tool RAMS are not enough
Use a task-specific assessment and method for work where tool hazards depend on specialist selection, competence, permits, rescue or emergency controls. Examples include abrasive-wheel mounting and cutting, chainsaw use, cartridge-operated fixing, concrete sawing, breaking or chasing, hot work, confined spaces, roof or façade work, work near explosive atmospheres, and any electrical work requiring a safe-isolation procedure.
The existing angle-grinder and abrasive-cutting guide, drilling and fixings guide and sanding and surface-preparation guide address those activities in more depth. A general document should point to them rather than dilute their controls.
When should work stop and the RAMS be reviewed?
Stop if the task, material, tool, accessory, power source, work area or expected exposure differs from the approved register. Also stop for unknown building fabric, suspected asbestos, hidden services, defective equipment, missing guards, incompatible accessories, uncontrolled dust, excessive vibration, unusual heat or noise, battery damage, loss of extraction, unstable access or people entering the exclusion area.
A competent person should review the changed conditions, update the assessment and method, and brief affected workers before work restarts. A signature on the original briefing is not permission to improvise a different tool or task.
Can a portable power tools RAMS template be used?
A template can help structure the document, but it cannot select the tool, accessory, material, extraction, exposure limits, access or exclusion arrangements for a live project.
The Portable Power Tools – General Use RAMS template is currently available in the IMERI H&S Partners RAMS shop as a downloadable digital template. Its verified product scope is general portable-tool use, and the product page requires the user to specify each tool, attachment, material and work task.
A competent person must assess and adapt the template to the project, tools, manufacturer information, tasks, materials, work area, workforce, exposures and site rules, then brief the people doing the work. Buying or completing a template does not make it automatically approved, suitable or site-ready.
When is project-specific RAMS support useful?
Support can help when a package combines several tools, trades or materials; exposure information is unclear; Principal Contractor comments need a technical response; or the general method must connect with more detailed drilling, cutting, sanding, access or COSHH controls.
For projects in Watford, Hertfordshire, London and the South East, send the work scope, locations, tools and accessories, materials, manufacturer information, power arrangements, expected durations, access, surveys, site rules and deadline. IMERI H&S Partners can confirm an appropriate scope for project-specific RAMS writing or review.
Official sources
This guide was checked on 11 November 2026 against the following current official sources:
- HSE: Provision and Use of Work Equipment Regulations (PUWER) overview
- HSE: Inspection of work equipment
- HSE: Maintenance of work equipment
- HSE: Electrical systems on construction sites
- HSE: Construction dust
- HSE CIS69: Controlling construction dust with on-tool extraction
- HSE: Construction noise
- HSE: Hand-arm vibration regulations
- HSE: Hand-arm vibration exposure calculator