RAMS for sealants, adhesives and expanding foam should identify the exact product, approved use, substrate, quantity, application method, work area, ventilation, exposure controls, access, curing restrictions and inspection standard before a container is opened. They should then explain preparation, controlled application, cleanup, waste handling, segregation and release.
“Apply sealant” is not a complete method. Acrylic, silicone, polyurethane, hybrid, epoxy, solvent-based, water-based, cyanoacrylate and expanding-foam products can have materially different hazards, compatibility limits, application conditions and curing requirements.
Connect the method with the project's COSHH assessments, the relevant installation guide and the Construction Phase Plan. Do not copy one product's controls to another merely because both arrive in a cartridge or can.
Define the product, location and work boundary
State the rooms, façades, joints, penetrations, frames, skirtings, sanitaryware, floor edges or other interfaces included. Identify whether the task covers delivery, storage, surface preparation, masking, cartridge application, trowel or brush application, single-component foam, trimming, cleaning, inspection and protection.
Use the current specification, drawings, schedules and manufacturer instructions. Record the product name and intended use, not only “sealant” or “adhesive”. Confirm the approved substrate, joint size, backing material, primer, temperature, moisture and curing conditions instead of inventing technical acceptance criteria.
Define responsibility for design and product selection. Routine application RAMS should not decide movement-joint geometry, structural bonding, façade retention, fire performance, acoustic performance or chemical compatibility where those matters require design or specialist confirmation.
What information should be obtained before work starts?
Confirm, where relevant:
- the latest drawings, schedules, specification, approved product and any authorised substitution;
- the joint, interface or component location, dimensions, substrate, condition and acceptance criteria;
- current labels, safety data sheets, technical data and manufacturer application instructions;
- whether the product contains isocyanates, solvents or other substances requiring specific exposure controls;
- the intended quantity, duration, frequency and application method, including whether any mist or aerosol can be generated;
- room volume, openings, natural or mechanical ventilation, nearby air intakes and occupied-area interfaces;
- surface-preparation materials, primers, cleaners, release agents and waste produced by the task;
- cartridge guns, foam guns, mixing equipment, hand tools, access equipment and inspection arrangements;
- ignition sources, hot work, temporary heating, electrical equipment and combustible materials in the area;
- skin, eye, inhalation, spill, first-aid, washing, storage and emergency requirements;
- curing time, exclusion, protection, ventilation and reopening restrictions; and
- records, samples, batch information, adhesion checks or quality inspections required by the project.
Use a controlled preparation, application and release sequence
A project-specific sequence may cover:
- confirming the released area, approved details, specified product, substrate and inspection points;
- checking labels, safety data, expiry or shelf-life information, container condition and storage history;
- establishing access, lighting, ventilation, barriers, protection, washing and emergency arrangements;
- removing incompatible materials and preparing the substrate by the approved controlled method;
- checking joint dimensions, backing material, masking and primer requirements before application;
- opening, fitting or mixing only the quantity needed and keeping containers closed when not in use;
- applying the product with the specified tool and controlling drips, splashes, vapour, mist and unintended expansion;
- tooling, finishing and removing masking without spreading uncured material;
- cleaning equipment and handling wipes, empty containers and unused product under the assessed controls;
- maintaining ventilation, segregation and protection for the required cure period;
- inspecting the completed work and recording defects or corrective action; and
- releasing the area only when the specified cure, ventilation and acceptance conditions are met.
Critical controls to address in sealant, adhesive and foam RAMS
Product identity, compatibility and substitution
Check the specified system before work. A similar colour, trade description or packaging format does not establish compatibility with the substrate, primer, adjacent membrane, coating or previous product. Stop if the product, batch, expiry, substrate or detail differs from the approved information.
Do not substitute a solvent-based, two-part, isocyanate-containing or faster-curing product simply because the original is unavailable. A substitution can change exposure, ventilation, fire, mixing, curing and quality controls and needs the project's approval route and a revised assessment.
Isocyanates and expanding foam
HSE identifies polyurethane foams and glues among construction products that may contain isocyanates. The assessment should consider the product, method, quantity, people exposed and enclosure of the work area. Check the label and safety data rather than assuming that all expanding foam has the same composition.
Prevent or reduce exposure where reasonably practicable, including by selecting a suitable lower-hazard product and avoiding unnecessary spraying. Provide adequate fresh air, prevent skin and eye contact and select RPE only from the assessed contaminant and task. A particulate-only filter does not protect against vapours. Workers should understand relevant symptoms and the reporting procedure; health surveillance depends on the assessed exposure and legal requirements.
Solvents, vapours, fire and enclosed areas
Solvents can be present in glues, cleaners, primers and coatings. HSE notes that vapours are released during application, drying and curing and can build up in poorly ventilated spaces. Reduce solvent content where practicable, use the minimum quantity, keep containers closed and provide suitable ventilation or extraction for the actual task.
Identify ignition sources and combustible material before work. Control heaters, hot work, smoking, sparks and unsuitable electrical equipment where flammable vapour may be present. A small room, riser, cupboard or poorly ventilated void may need controls beyond open windows; stop and seek competent review if the assessed ventilation cannot be achieved.
Skin, eye contact and hygiene
Acrylic sealants, epoxy resins, hardeners, solvents and glues can contribute to dermatitis or other harm. Prevent direct contact through the work method and suitable tools before relying on gloves. Select glove material and breakthrough performance for the actual product and duration using manufacturer or supplier information.
Provide eye protection where splashes or pressurised discharge are possible, washing facilities and a method for dealing with contamination. Do not clean skin with solvents. Brief the product-specific first-aid action and ensure uncured material is not transferred to handles, phones, welfare areas or completed surfaces.
Pressurised containers, application tools and access
Inspect pressurised foam cans, cartridge guns, nozzles and mixing tools before use. Keep containers within the manufacturer's storage and use conditions, protect them from damage and heat, and follow product instructions for fitting, cleaning and disposal. Isolate or make safe equipment before clearing a blockage; do not improvise by puncturing or heating a container.
Select suitable access equipment for the height, duration, reach and work position. Do not overreach from a stepladder while controlling a gun, working overhead or handling an open product. Protect people and finishes below, manage trailing extraction or lighting cables, and keep escapes clear.
Ventilation, occupied areas and curing
Define how fresh air will reach the work area and where contaminated air will go. Ventilation should not move vapour or odour into occupied rooms, public areas or air intakes. Segregate non-essential people where exposure, wet product, pressurised application or incomplete joints present a risk.
State the required curing, ventilation and protection period from the approved product information. Prevent premature cleaning, covering, loading, water exposure or occupation. If the product remains tacky, expands unexpectedly, produces unusual vapour, fails to cure or affects an adjacent material, stop and follow the defect and review process.
What should inspection and handover cover?
Define who checks the substrate, backing material, primer, joint preparation, product and batch, application, finish, cure and protection. Where the specification requires samples, adhesion tests, photographs, batch records or inspection before work is concealed, identify the hold point and acceptance authority.
Final checks should address continuity, dimensions, adhesion, voids, contamination, overspill, damage, staining, curing, cleanliness and protection. Record defects and corrective work rather than masking a failed joint or adding an incompatible product over it.
When should the RAMS and COSHH controls be reviewed?
Review the method when the product, substrate, detail, quantity, application method, room, ventilation, access, workforce, programme, temperature, moisture, curing or inspection requirement changes. Stop and reassess after an unapproved substitution, damaged container, blocked nozzle, uncontrolled discharge, spill, unexpected vapour, skin or breathing symptom, failed cure, incompatible reaction, near miss or instruction that changes the work.
Brief the workforce on product identity, application limits, ventilation, exclusion, PPE, hygiene, first aid, storage, waste, cure time and stop-work conditions. Principal Contractor acceptance does not make a generic method suitable or transfer the contractor's responsibility for its product and work.
When routine application RAMS are not enough
This scope does not cover spray-applied polyurethane foam insulation, high-volume isocyanate spraying, structural bonding, safety-critical resin anchors, façade retention, specialist injection, confined-space work or application where a designed fire-stopping system or another certified installation process is required.
It also does not replace the specification, design details, manufacturer instructions, COSHH assessment, safety data, substrate testing, ventilation design, access plan, inspection plan, occupational-health arrangements or competent specialist input required for the actual system.
Can a sealants, adhesives and expanding foam RAMS template be used?
A relevant template can provide a useful structure, but it cannot know the specified product, substrate, joint, quantity, room, ventilation, access, exposure, cure or inspection standard for the project.
The Sealants, Adhesives & Expanding Foam RAMS template is available in the IMERI H&S Partners RAMS shop. Check that its named scope matches the actual work. A competent person must assess and adapt it to the project, specified product, safety data, substrate, application method, area, ventilation, equipment, workforce and Principal Contractor requirements, then brief the workforce.
Buying or completing a template does not make it automatically approved, suitable or site-ready. It does not replace product selection, technical data, COSHH assessment, competent supervision, inspection or the contractor's responsibility for the work.
When is project-specific RAMS support useful?
Support may be useful where several products or substrates are involved, work is repetitive or enclosed, occupied areas remain nearby, product substitution is proposed, access is restricted, interfaces are safety-critical or generic RAMS have been returned for revision.
For projects in Watford, Hertfordshire, London and the South East, send the drawings or joint schedule, specification, product and safety data, substrates, quantities, application method, work areas, ventilation and access arrangements, cure and inspection requirements, programme and Principal Contractor rules. IMERI H&S Partners can then confirm an appropriate scope for project-specific RAMS support.
Official sources
This guide was checked on 6 November 2026 against the following current official sources: